Waterjet Group

JE5SEJAMES · JE5SEJAMES

Ok, My Company Just Got A Flow A Month Or 2 Ago. When I Cut Lexan (1/4" and 1/8"), I Get "Clouds" On The Glass Where The Slats Are. Furthermore, Occasionally In These Same Spots, It Blasts Off Pieces Of The Material And Leaves A "Nick" On The Corners Of The Material. It Ha...

qsudbury · qsudbury

Has anyone put a flow cutting head on an omax machine?

Barney · Barney

I am not sure if this is appropriate for this forum but I am sure I will find out if not but I recently purchased a used Flow 20X 100HP pump and I am looking for a chiller for the hydraulic heat exchanger. Anyone have any suggestions?

waterjetphilippines · waterjetphilippines

Hello, what is your typical settings for flowcut with regards to dwell times for jet on/abrasive on and jet off/abrasive off? I want to be able to cut the fastest, does the waterjet need to dwell for a few seconds between jet and abrasive.

AR-HYPERJET · AR-HYPERJET

What is the demand for waterjetting metals products?

austinz32 · austinz32

i have a mitsubishi dx612 with a kmt 90k pump. the height adjustment i guess faulted out while in the middle of cutting 5" carbon and broke the mixing tube. the jet before this was a 60k direct drive flow and if this ever accord it was easy to slide a paper clip up into the mixing chamber loop one end an...

kzman70 · kzman70

does anyone know of a waterjet company in the Salt lake valley or utah calley? thanks

samuel · samuel

Samuel son and Co. in Hayward Ca. is currently lookin for an Operator for our FLOW WMC.

Steve Goodman · Steve Goodman

I am having a continuous problem with the machine stopping due to pump health problems; the fault appears to be poppet valve related? There have been five sets replaced in around 100 hours threes sets by flow engineers. Is any one else suffering the same problems? The machine is two years old model Hyp...

waterjetphilippines · waterjetphilippines

I'm running a Direct Drive Hyplex Pump 55k @30hp, I'm currently running it at 53.5~54k psi cutting pressure. Should I maximize it at 55k or just maintain slightly lower psi to lessen the stress on the pump? Since it's rated at 55k psi, running it at 55k would be a fluctuation of 55k~55.5k on the gaug...

boise_shull · boise_shull

Hi! i run a 87k flow ifb with dynamic and ultra pierce. we just got the 100pound mini hopper and im having some troubles. does anyone else use this machine? and more specifically, has anyone added a mini hopper to it? questions include, best way to run the additional delivery line, and im also having so...

Scott · Scott

I run a Calypso Hammerhead Mark IID. When I start to run my pattern about one quarter of the way thru the cutting head start to lose home and drift ever so slowly to the yb side. By the end of the pattern the cutting head is off by about a quarter inch. I am not getting any faults and the machine returns to soft h...

Scott · Scott

Looking for a good and relieble source for table bricks and garnet. Any suggestions please?

tomasmacej · tomasmacej

I have simple question. Simple? Why is it necessary to examine the cut surface area? Make your opinion. THX

cmngnscrwd · cmngnscrwd

Saw a thing on the food network about a company called "Wholly Guacamole" (cool name, or what?!?) that uses a machine that puts so much pressure on the packaged product that it kills the bacteria in it. I forget the name they gave to the process, but basically it's like cold pasteurization...

JetChick · JetChick

I'm curious how long I should be able to cut on my material support slats before I need to replace them? Thank you!

Topic		Started By	Replies	Views	Last Post
	Best Way To Cut Lexan(Plexiglass) (Preview) Ok, My Company Just Got A Flow A Month Or 2 Ago. When I Cut Lexan (1/4" and 1/8"), I Get "Clouds" On The Glass Where The Slats Are. Furthermore, Occasionally In These Same Spots, It Blasts Off Pieces Of The Material And Leaves A "Nick" On The Corners Of The Material. It Ha...	JE5SEJAMES	4	10391	Jul 15, 2010 by JE5SEJAMES
	Flow Head on Omax (Preview) Has anyone put a flow cutting head on an omax machine?	qsudbury	1	4482	Jun 2, 2010 by TFabian
	Flow 20X Pump Chiller (Preview) I am not sure if this is appropriate for this forum but I am sure I will find out if not but I recently purchased a used Flow 20X 100HP pump and I am looking for a chiller for the hydraulic heat exchanger. Anyone have any suggestions?	Barney	1	4061	May 21, 2010 by Topend1
	Dwell times for jet and abrasive (Preview) Hello, what is your typical settings for flowcut with regards to dwell times for jet on/abrasive on and jet off/abrasive off? I want to be able to cut the fastest, does the waterjet need to dwell for a few seconds between jet and abrasive.	waterjetphilippines	7	47822	May 21, 2010 by scott hines
	water jet demands (Preview) What is the demand for waterjetting metals products?	AR-HYPERJET	3	11603	May 20, 2010 by TFabian
	a little help (Preview) i have a mitsubishi dx612 with a kmt 90k pump. the height adjustment i guess faulted out while in the middle of cutting 5" carbon and broke the mixing tube. the jet before this was a 60k direct drive flow and if this ever accord it was easy to slide a paper clip up into the mixing chamber loop one end an...	austinz32	1	3103	Mar 11, 2010 by austinz32
	Utah Company (Preview) does anyone know of a waterjet company in the Salt lake valley or utah calley? thanks	kzman70	0	2745	Mar 4, 2010 by kzman70
	looking for operator (Preview) Samuel son and Co. in Hayward Ca. is currently lookin for an Operator for our FLOW WMC.	samuel	0	3059	Feb 10, 2010 by samuel
	Pump Health warning problems (Preview) I am having a continuous problem with the machine stopping due to pump health problems; the fault appears to be poppet valve related? There have been five sets replaced in around 100 hours threes sets by flow engineers. Is any one else suffering the same problems? The machine is two years old model Hyp...	Steve Goodman	3	3863	Feb 7, 2010 by Waterjet Guy
	Direct Drive Hyplex Pump (Preview) I'm running a Direct Drive Hyplex Pump 55k @30hp, I'm currently running it at 53.5~54k psi cutting pressure. Should I maximize it at 55k or just maintain slightly lower psi to lessen the stress on the pump? Since it's rated at 55k psi, running it at 55k would be a fluctuation of 55k~55.5k on the gaug...	waterjetphilippines	1	3462	Jan 14, 2010 by biglmf1127
	additional mini-hopper help (Preview) Hi! i run a 87k flow ifb with dynamic and ultra pierce. we just got the 100pound mini hopper and im having some troubles. does anyone else use this machine? and more specifically, has anyone added a mini hopper to it? questions include, best way to run the additional delivery line, and im also having so...	boise_shull	3	3601	Jan 8, 2010 by Topend1
	Need Help (Preview) I run a Calypso Hammerhead Mark IID. When I start to run my pattern about one quarter of the way thru the cutting head start to lose home and drift ever so slowly to the yb side. By the end of the pattern the cutting head is off by about a quarter inch. I am not getting any faults and the machine returns to soft h...	Scott	3	4190	Dec 14, 2009 by Topend1
	Table bricks and garnet (Preview) Looking for a good and relieble source for table bricks and garnet. Any suggestions please?	Scott	1	3028	Dec 14, 2009 by Topend1
	Why is it necessary to examine the cut surface area? (Preview) I have simple question. Simple? Why is it necessary to examine the cut surface area? Make your opinion. THX	tomasmacej	1	16792	Nov 19, 2009 by cmngnscrwd
	High pressure food pasteurization thingy (Preview) Saw a thing on the food network about a company called "Wholly Guacamole" (cool name, or what?!?) that uses a machine that puts so much pressure on the packaged product that it kills the bacteria in it. I forget the name they gave to the process, but basically it's like cold pasteurization...	cmngnscrwd	1	3761	Nov 5, 2009 by TFabian
	How long should my support material slats last? (Preview) I'm curious how long I should be able to cut on my material support slats before I need to replace them? Thank you!	JetChick	5	6163	Oct 24, 2009 by waterjetphilippines
«First < 1 … 7 8 9 \| Page of 9 sorted by